Accessories

CUE System Serial Cable 5-pin to RJ-14

SKU: CA0183

RS-485 serial cable between controller / interface and power switching units, dimmers and interfaces.

Out of stock

Notify when in stock

CUE System Serial Cable 3-pin to RJ-14

SKU: CA0184

RS-485 serial cable between controller and power switching units, dimmers and interfaces.

Out of stock

Notify when in stock

CUE System Wall Set 55

SKU: CS0583

Wall set for installation of "55" units on the wall This set allows to install interface on the wall. It is fully compatible with standard electrical wall boxes.

Out of stock

Notify when in stock

CUE System Pan Adapter 55

SKU: CS0584

Adapter for conversion from non-CUE ready PANCONNECT boxes This adapter allows to install interface into PANCONNECT boxes that are not prepared for CUE products.

Out of stock

Notify when in stock

CUE System Opto-Input Adapter /i

SKU: CS0257

Any status indicator on the controlled device can be read using the Opto-Input Adapter /i photosensitive cell. The Opto-Input Adapter /i is fastened on the indicator using a double-sided adhesive tape.

Out of stock

Notify when in stock

CUE System Tabletop Holder 55

SKU: CS0586

Holder for installation of "55" units on the top of the desk Allows to install interface on the top of the table. It attaches on the top side of the table desk

Out of stock

Notify when in stock

CUE System Under Desk Holder 55

SKU: CS0587

Holder for installation of "55" units under the desk This holder allows to install interface under the table. It attaches to the under side of the table desk.

Out of stock

Notify when in stock

CUE System PoE Adapter, Power over Ethernet injector

SKU: CS0327

The PoE Adapter is fully compliant with the IEEE802.3af standard. It delivers up to 15.4 W output power per port. By using this device, both data and electrical power can be simultaneously delivered through a single CAT5 (or better) Ethernet cable to a non-PoE Ethernet-enabled device, eliminating the trouble to connect it to an outlet nearby with an external power cord. You can connect it to a wireless AP, Webcam (IP Camera), IP telephone, or other IEEE802.3af compliant devices to reduce installation costs and improve your network performance.

Out of stock

Notify when in stock

CUE System NFC Reader, xtension NFC reader for 7" & 10" panels in "M" version (HW revision 22 and higher)

SKU: CS0618

The NFC Module is an expansion accessory for touchONE and touchCUE panels. It enables the use of NFC technology in the touchONE reservation system as well as in the CUE control system. This module is not compatible with built-in touch panels. To set up NFC functions in the touchONE reservation system, it is necessary to use the touchONE-admin management system. Ask for software availability. Functions for using NFC in the control system are available as part of the Cue Visual Composer programming tool.

Out of stock

Notify when in stock

CUE System IR Adapter Set

SKU: CS0553

The IR Adapter Set is set of five infrared emitters. Every infrared emitter cable can be used for controlling AV devices equipped with IR control capabilities. LED emmiter is fastened on the receiver window using a double-sided adhesive tape.

Out of stock

Notify when in stock

CUE System Rack Mounting Shelf

SKU: CS0449

The Rack Mounting Shelf is an optional mounting accessory for controllers and IP interfaces. It allows secure installation of the devices in a 19” EIA equipment rack. The Rack Mounting Shelf occupies 1 rack space and it allows to install one full rack width unit, two half rack width units, four quarter rack width units or any possible combinations. The delivered faceplates can hide any open position on the shelf. Rackmounting hardware is not supplied.

Out of stock

Notify when in stock

CUE System Terabee People Counting M White

SKU: TB-PCM-W

Out of stock

Notify when in stock

CUE System Terabee People Counting L-XL White

SKU: TB-PCL-XL-W

Out of stock

Notify when in stock

CUE System signCUE-two, Graphic player and interface for HID compliant touch screens

SKU: CS0592

The signCUE-two is a powerful IP-enabled unit that serves as a controller, server, touch monitor interface, and display device interface. It runs standard projects created in Cue Visual Composer and allows to combine custom graphical environment with controls for AV, lighting, drapes, HVAC, and other technologies. The signCUE-two provides an HDMI 2.0 output for connection to the display device and includes a USB HID port for touch screen connection. The Ethernet provides a connection to other Cue System units as well as a control port for IP-controlled devices. The player is enclosed in a compact chassis and can be easily installed behind a flat display or projector, under a table, or inside a rack.

Out of stock

Notify when in stock

Electro Waves

Information

Contact us

Site map